Wilton JWBS-16B Instrukcja Użytkownika

Operating Instructions and Parts Manual 16-Inch Woodworking Band Saw Model JWBS-16B WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVe

10 Adjusting Blade Tension 1. Disconnect machine from the power source, unplug. 2. Turn blade tension hand wheel (E, Fig. 2) counter-clockwise to t

11 Lower Blade Guide Adjustment Disconnect machine from the power source, unplug before making any adjustments! Blade teeth are sharp! Use care when

12 Mounting the Table 1. Mount the trunnion support bracket (A, Fig. 5) to the bandsaw with four 5/16” x 1-1/2” hex cap bolts, and four 5/16” lock w

13 Rail Assembly (optional accessory) 1. Attach the front rail (A, Fig. 8) to the cast iron table with two 1/4” x 5/8” hex cap bolts, two 1/4” lock

14 4. Check the clearance between the table and the fence. The gap should be the same at the front of the table as it is at the rear. If the gap w

15Tilting the Table 1. Disconnect the machine from the power source, unplug. 2. Loosen the lock knobs (A, Fig. 13). 3. Tilt table up to 45 degree

16Changing Blades Disconnect machine from the power source, unplug! Blade teeth are sharp! Use care when handling the saw blade. Failure to comply

17Replacing V-Belt 1. Disconnect the machine from the power source. 2. Release blade tension by turning blade tension hand wheel clockwise. 3. Rele

18Electrical Connections All electrical connections must be done by a qualified electrician! Failure to comply may result in loss of property and/or

19Troubleshooting Trouble Possible Cause Solution Saw stops or will not start 1. Saw unplugged 2. Fuse blown or circuit breaker tripped 3. Cord dama

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20Upper Wheel Assembly Index No. Part No. Description Size Qty 1 ... JWBS16B-101 ...Saw Body...

21Upper Wheel Assembly

22Lower Wheel and Motor Assembly Index No. Part No. Description Size Qty 1 ... JWBS18-201 N ...Bearing Base...

23Lower Wheel and Motor Assembly Index No. Part No. Description Size Qty 52 ... TS-0680031 ...Flat Washer...

24Blade Guides Assembly Index No. Part No. Description Size Qty 1 ... TS-0051051 ...Hex Cap Screw ...

25Blade Guides Assembly

26Table Assembly Index No. Part No. Description Size Qty 1 ... JWBS16-401 ...Table ...

27Table Assembly

28Fence & Miter Assembly (optional accessory) Index No. Part No. Description Size Qty 1 ... JWBS18-401 ...Lock Kno b ..

29Fence & Miter Assembly (optional accessory)

3 Table of Contents Warranty and Service...

30Wiring Diagram

31Notes

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-27

4 Warning 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings poste

5 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking ar

6 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for model JWBS-16

7 Grounding Instructions This machine must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or br

8 Unpacking Remove the packing material from the band saw. Note: Remove the plywood and bolts from the base. Inspect the machine for damage. Report

9 Assembly and Setup Base Support Extension 1. Attach straps (A, Fig. 1A) to extension base (B, Fig. 1A) with (2) 5/16-18 button head cap screws (C